DocumentationDocumentation
Technical reference
Configuration, wiring and service instructions linked from the device manuals.
- Configuration with WB-MIO / WB-MIO-E
- Configuration with WB-MGE v.3
- Operating, storage and transport conditions
- Digital inputs and dry contacts
- Connecting open-collector outputs
- WBIO-DI-HVD-16 known issues
- Counting pulses with wb-rules
- WB-MCM8 hardware pulse counters
- Controller web interface and user access
- Release wb-2602
- Wiren Board 6: expansion modules
- Wiren Board 7: expansion modules
- Wiren Board 8: expansion modules
- Opening the controller enclosure
- Opening Wiren Board 6
- Opening Wiren Board 7.2–7.3
- Opening Wiren Board 7.4
- Opening Wiren Board 8.5
- Opening Wiren Board 8M
- 1-Wire bus wiring
- Grounding and GND/iGND connections
- RS-485 wiring and supply voltage drop
- Adding and configuring Modbus devices
- Modbus RTU, addressing and communication settings
- Configuration without a Wiren Board controller
- Firmware updates, bootloader and factory reset
- Relay mapping matrices, timers and frequency
- Relay loads and interference suppression
- WB-M1W2 and WB-MR6C version differences
- WB-M1W2 v.3 Modbus register map
- Relay module Modbus register map
- WB-M1W2 v.3 firmware changelog
- WB-MR6C v.3 firmware changelog
- WB-M1W2 v.3 hardware revisions
- WB-MR6C v.3 hardware revisions
- WB-M1W2 v.3 known issues
- WB-MR6C v.3 known issues
- WB-MIR v.3 Modbus register map
- WB-LED Modbus register map
- WB-MAP3E measurement registers
- WB-MAP3E configuration registers
- WB-LED firmware changelog
- WB-LED known issues
- WB-LED hardware revisions
- WB-MIR v.3 firmware changelog
- WB-MIR v.3 known issues
- WB-MIR v.3 hardware revisions
- WB-MAP3E firmware changelog
- WB-MAP3E known issues
- WB-MAP3E hardware revisions
- Recording, playing and backing up IR commands
- Selecting LED strip cable cross-section
- How WB-MAP calculates line-to-line voltage
- WB-LED software and controller setup
- WB-MAP installation and commissioning
- WB-MAP measurement terminology
- Current transformer selection and accuracy
- Using WB-AMPLED with WB-LED
- Node-RED integration for IR control
- WB-MRPS6 hardware revisions
- WB-MRPS6 firmware changelog
- Hongfa HF115F-S relay
- WB-MRPS6 known issues
- WB-MDM3 hardware revisions
- WB-MDM3 firmware changelog
- WB-MDM3 Modbus register map
- WB-MDM3 software and configuration
- WB-MDM3 known issues
- WB-MAI6 hardware revisions
- WB-MAI6 firmware changelog
- Type K sensor characteristic
- Pt100 sensor characteristic
- NTC100k B3950 sensor characteristic
- NTC10k B3950 sensor characteristic
- NTC10k B3988 sensor characteristic
- NTC10k B3435 sensor characteristic
- NTC10k B3470 sensor characteristic
- NTC5k B3470 sensor characteristic
- NTC1k8 B3380 sensor characteristic
- WB-MAI6 known issues
- YHDC HSTS016L current sensor
- WB-VDIV voltage divider
- WB-MAI6 comparison with earlier modules
- WB-MAI6 Modbus register map
- Sensor conversion and scaling
- WB-MWAC v.2 hardware revisions
- WB-MWAC v.2 firmware changelog
- MWAC v.2 Modbus register map
- WB-MWAC software and configuration
- WB-MWACv2 known issues
- WB-MRM2-mini hardware revisions
- WB-MRM2-mini firmware changelog
- WB-MRM2-mini known issues
- WB-UPS v.3 hardware revisions
- WB-UPS v.3 firmware changelog
- WB-UPS v.3 Modbus register map
- WB-UPS v.3 known issues
- T13 frequency converter: motor-control reference
- WB-UPS v.2: legacy model comparison
- WB-MWAC v.1: legacy model comparison
- WBE2R-R-ZIGBEE v.2 known issues
- Updating Zigbee module firmware
- WBE2R-R-ZIGBEE v.1 legacy module
- WBIO-DI-WD-14 first-revision wiring
- Zigbee setup and troubleshooting
- WB-MGE v.3 firmware changelog
- WB-MGE v.3 known issues
- WB-MGE v.3 custom firmware and GPIO
- WB-MGE v.3 hardware revisions
- Wiren Board 8 known issues
- Wiren Board 8 hardware revisions